Domino KurzhubGasgriff für Flachschieber + orig. Vergaser


€ 72,65 inkl. MwSt. zzgl. Versand

Bestellen


(English description below)

Spezialgasgriff mit kurzem Weg für 2 Gaszüge.

Gasgriff mit extra kurzen Drehwinkel, zusammen mit dem Gaszug für Flachschieber ausgezeichnet für die Flachschiebervergaser geeignet.

Kann aber ebenso auch am originalen Vergaser verwendet werden, dazu aber auch Produkt 211 - HRT Gaszug für Flachschieber verwenden!

ACHTUNG
Dieser Gasgriff kann nicht für die XF650 Freewind verwendet werden, weil wir dafür keinen passenden Gaszug haben!

Technik
Domino:
- max. Drehwinkel: 124°
- Wirkdurchmesser des Seilzuges: 45,5mm
- daraus max. möglicher Seilzug: 49,3mm
Da aber der Flachschieber nur 25mm braucht, ist nur eine Drehbewegung von 63° möglich.

Zum Vergleich der originale Gasgriff:
- max. Drehwinkel: 120°
- Wirkdurchmesser des Seilzuges: 35,5mm
- daraus max. möglicher Seilzug: 37,2mm
Da aber der Flachschieber nur 25mm braucht, ist nur eine Drehbewegung von 80,7° möglich

Fazit
Der Domino hat 17,7° weniger Drehwinkel!
Du musst also beim Gas geben nicht nachgreifen und Dein Handgelenk ist viel entspannter, weil es nicht ständig so weit drehen muss. Ganz nebenbei kannst Du beim Beschleunigen auch viel einfacher und schneller mal alle PS abfordern :-).

Natürlich kannst du den Gasgriff auch für Deine Originalvergaser benutzen.
Achtung!! Der Gaszug für Flachschieber sollte allerdings dabei Verwendung finden.
Beim Originalvergaser immer zusammen verbauen mit:
Produkt 211 - HRT Gaszug für Flachschieber

Wichtig
Der Gaszug "Flachschieber" wird rechts vom Gasgriff kommend hinter dem Lenker verlegt. Er wird dann links am Tank beim Steuerkopf eingeführt und geht von da aus direkt zum Vergaser. Vorteil: weniger Kabelgewirr, weniger Seilzug-Längenänderung beim Einschlagen.

Zubehör:
Produkt 211 - HRT Gaszug für Flachschieber

 

DOMINO SHORT-STROKE THROTTLE GRIP FOR FLAT SIDE AND ORIGINAL CARBURETTOR

Special throttle grip with short stroke for 2 throttle cables.

Throttle grip with extra short rotation angle, perfect for the flat slide carburettor when using the special throttle cable for flat side carbs.

It can also be used with the genuine carburettor, but you have to use product 211 - HRT Throttle Cable for Flat Side Carb!

Technic
Domino:
- Max. Rotation angle: 124 °
- effective diameter of the cable: 45.5mm
- from this max. possible cable pull: 49.3mm
But because the flat side only needs 25mm, only a rotation of 63 ° is possible.

For comparison, the original throttle:
- Max. Rotation angle: 120 °
- effective diameter of the cable: 35.5mm
- from this max. possible cable: 37,2mm
But because the flat side only needs 25mm, only a rotation of 80.7 ° is possible

Conclusion
The Domino has 17.7° shorter rotation angle!
So you do not have to displace your hand so often and your wrist is much more relaxed due to the much shorter cable way. By the way, you can accelerate much easier and faster times demanding all power :-).

Of course, you can also use the throttle grip for your genuine carburettor.
Attention!! The throttle cable for flat slide should also be used with the genuine carburettor.
Always assemble with:
Product 211 - HRT Throttle Cable for Flat Side Carb

Important
The throttle cable for flat side carbs is installed behind the handlebar on the right side of the throttle. It has to be inserted left side of the tank at the steering head and goes from there straight to the carburettor.
Advantage: less cable tangle and less movement of the cable while steering.

Compatible products:
Product 211 - HRT Throttle Cable for Flat Side Carb

Menü